56 years later and still the WC apologists deny the conspiracy.

[Tim Nickerson]

Nice. Very nice. Like this one. I'm still waiting for one of the geniuses here to tell me how in the XXXX that bullet went upward and out of the neck...

The bullet never went upward. It's trajectory was always downward.

[Jerry Freeman]

What point? You refuse to engage in the details because you are woefully ignorant of them. You’re here to play games and try to look “clever”.
  I'm still waiting for one of the geniuses here to tell me how in the XXXX that bullet went upward and out of the neck...

http://www.thesmokinggun.com/file/autopsy-descriptive-sheet-0 

The bullet never went upward. It's trajectory was always downward.

If that is true...according to the autopsy notes above....the bullet should have gone downward into the center of the chest.

[Tim Nickerson]

http://www.thesmokinggun.com/file/autopsy-descriptive-sheet-0 
If that is true...according to the autopsy notes above....the bullet should have gone downward into the center of the chest.

According to the notations on that Face Sheet, the bullet entered 14 cm below the tip of the right mastoid process.  Correct?  The downward angle of trajectory would have had to be a hell of a lot greater than 17.5 degrees in order for the bullet to enter the center of the chest. Jerry Organ has a superb graphic explaining the path through Kennedy. Have you ever seen it?

[Jack Trojan]

This graphic by unknown appears to show the missile channel would have passed by the spine at the T1 level. But it's obvious the skull overlay is too small, which draws upward the cervical vertebrae.

When are you going to accept that you can't measure a 2D image this way? Your POV is never a perfect profile and all measurements are distorted. This is not how photogrammetry is done. Do the damn 2 laser challenge if you actually care about the truth and you want to advance your argument. Otherwise, your graphics are worse than misleading.

[Jerry Freeman]

You can sit around and let these clowns [who weren't there] tell you what happened if you want--- or you can hear what really happened from the doctors who attended President Kennedy at Parkland. 

[Martin Weidmann]

I see Jones confirming the tracheotomy cut had been large to allow exploration and that the head wound was on the upper top right.

McClellan was standing over Kennedy and could see the gaping wound was at the back of Kennedy's skull? Not possible. Jenkins is keeping Kennedy's head face-up.

McClellan was standing over Kennedy and could see the gaping wound was at the back of Kennedy's skull? Not possible.

Says the guy who wasn't there and who could not possibly know what McClellan saw.

[Walt Cakebread]

I see Jones confirming the tracheotomy cut had been large to allow exploration and that the head wound was on the upper top right.

McClellan was standing over Kennedy and could see the gaping wound was at the back of Kennedy's skull? Not possible. Jenkins is keeping Kennedy's head face-up.

So you are saying that Doctor Mc Clelland is a liar......    Dr Mc Clelland said that he saw a huge hole in the lower right rear of JFK's head ..... His statement is verified by 18 witnesses who are shown in photos  on pages 86. 87. and 88 of Groden's,  TKOAP. (Incidentally one of those photos is of Doctor Ronald Jones, and in the photo Dr Jones is seen with his right hand with the fingers splayed depicting the large wound LOW on the rear of JFK's head  )   In the Video that was made 50 years later in 2013, Dr Jones contradicts his earlier photo and indicates that the wound on the rear of JFK's head was HIGH on the rear of JFK's head.   

Dr Mc Clelland comes across as much more credible than Dr Jones..... 

[Jack Trojan]

All the measurements apply to the mid-line and so are on the same plane. Practically no distortion.

Why can't one do photogrammetry and allow for perspective?

No, there is no POV from a 2D image that you can measure without ortho-recitfying it. You must "flatten" out the image to counteract the distortion created when you project a 3D object onto a 2D image. This is the only way to measure objects on a 2D image, which is what photogrammetry is all about; restoring the 3rd dimension from a 2D image. Since this is likely beyond your purview, your best bet is to create a digital 3D model of JFK, which you can manipulate graphically into the correct position to make the MB work, or not.  But you are relying on the CAD's physics engine to do all the work for you and in the end, who is going to buy it?

It's so much easier to skip the CGI and use 3D surrogates instead, which anyone can do even if you have no photo-analysis credentials. That is the beauty of a 3D re-enactment using lasers. It's cheap and deadly accurate and anyone can do it to convince themselves that the MB was either feasible or